Yasutaka IGARASHI Hiroyuki YASHIMA
We theoretically analyze the performance of coherent ultrashort light pulse code-division multiple-access (CDMA) communication systems with a nonlinear optical thresholder. The coherent ultrashort light pulse CDMA is a promising system for an optical local area network (LAN) due to its advantages of asynchronous transmission, high information security, multiple access capability, and optical processing. The nonlinear optical thresholder is based on frequency chirping induced by self-phase modulation (SPM) in optical fiber, and discriminates an ultrashort pulse from multiple access interference (MAI) with picosecond duration. The numerical results show that the thermal noise caused in a photodetector dominates the bit error rate (BER). BER decreases as the fiber length in the nonlinear thresholder and the photocurrent difference in the photodetector increase. Using the nonlinear optical thresholder allows for the response time of the photodetector to be at least 100 times the duration of the ultrashort pulses. We also show that the optimum cut-off frequency at the nonlinear thresholder to achieve the minimum BER increases with fiber length, the total number of users, and the load resistance in the photodetector.
Yasuyuki OZEKI Yuichi TAKUSHIMA Keiichi AISO Kazuro KIKUCHI
We design and demonstrate a high repetition-rate similariton generation system using normal dispersion fiber amplifiers (NDFA's). We numerically calculate the pulse evolution in NDFA's and clarify the condition to generate similariton pulses in a finite-length NDFA. Then we design the similariton generation system in consideration of the use of Erbium-doped fibers (EDF's) and show that a km-long fiber amplifier with low normal dispersion can generate a high repetition-rate similariton train from practical pico-second pulse sources. In the experiment, we demonstrate a 10-GHz similariton source using a 1.2-km-long EDF. For application to multi-wavelength light sources, we measure the bit-error rate of the spectrally sliced similariton, and show that it exhibits low-noise performance, which is attributed to the spectral flatness.
Kenichiro TSUJI Takuya WATANABE Noriaki ONODERA Masatoshi SARUWATARI
For wavelength conversion based on cross-gain modulation (XGM) and cross-phase modulation (XPM) in semiconductor optical amplifiers (SOAs), a CW assist light is quite effective for acceleration of carrier recovery and reduction of pattern effects. We theoretically study assist light conditions both for XGM- and XPM-based wavelength conversion by numerically simulating eye-diagrams. Taking into account the spatial and temporal variations of carrier density along the SOA length, we successfully clarify the dependences of wavelength, power, and propagation direction of the assist light, and reveal the principal difference of response characteristics between XGM and XPM depending on carrier modulation.
Takashi MORIE Kenichi MURAKOSHI Makoto NAGATA Atsushi IWATA
This paper presents circuit techniques using pulse-width and pulse-phase modulation (PWM/PPM) approaches for VLSI implementation of nonlinear dynamical systems. The proposed circuits implement discrete-time continuous-state dynamics by means of analog processing in a time domain, and also approximately implement continuous-time dynamics. Arbitrary nonlinear transformation functions are generated by the process in which a PPM signal samples a voltage or current source whose waveform in the time domain has the same shape as the desired transformation function. Because a shared arbitrary nonlinear voltage or current waveform generator can be constructed by digital circuits and D/A converters, high flexibility and real-time controllability are achieved. By using one of these new techniques, we have designed and fabricated a CMOS chaos circuit with arbitrary 1-D maps using a 0.6 µm CMOS process, and demonstrate from the experimental results that the new chaos circuit successfully generated various chaos with 7.5-7.8 bit precision by using logistic, tent and chaotic-neuron maps.
Hiroyasu SONE Masaaki IMAI Yoh IMAI Yasuhiro HARADA
It is found that the supercontinuum spectrum is generated from cross-phase modulated soliton pulses which are propagated through a dispersion-flattened/decreasing fiber with low birefringence. The cross-phase modulation is achieved by exciting two orthogonally polarized modes in a birefringent fiber and the effect of input azimuth of linearly polarized pulses is discussed theoretically and numerically.
In this letter, we investigate a diversity scheme which employs a simple transform, symbol interleaving and decision-feedback differential detection (DF-DD) for differential phase-shift-keying signal transmission over correlated Rayleigh fading. The proposed scheme merits instinct time diversity within each transmitted block and thus presents patent resistance to fading. It is shown that the considered technique provides significant diversity gains in a correlated Rayleigh fading channel.
The effectiveness and possible applications of all-optical wavelength conversion using optical fibers are described. Several types of ultra-broad and ultra-fast wavelength conversion using highly-nonlinear fiber are shown. Over 70 nm conversion band by four-wave mixing, 500-fs pulse trains conversion by cross-phase-modulation-based nonlinear optical loop mirror and time-based optical add-drop multiplexing for 160 Gbit/s signal using wavelength conversion by supercontinuum are successfully demonstrated.
Kazuhide NAKAJIMA Takuya OMAE Masaharu OHASHI
In this letter, we describe the conditions for measuring the nonlinear refractive index n2 when using the self-phase modulation-based cw dual-frequency method. We clarify the appropriate measurement conditions for dispersion-shifted and conventional single-mode fibers both numerically and experimentally. We also show experimentally that the evaluated n2 values for conventional single-mode fiber depend on the signal wavelength separation.
Akihide SANO Yutaka MIYAMOTO Tomoyoshi KATAOKA Masahito TOMIZAWA Kazuo HAGIMOTO
This paper proposes an automatic dispersion equalization system using extracted clock power monitoring in order to facilitate the field installation of high-speed time-division multiplexed (TDM) systems over existing fiber cables. The proposed scheme adjusts the dispersion of a variable-dispersion equalizer so as to maximize the extracted clock power level. This scheme has a simple configuration, needs no communication channel between the transmitter and the receiver, and is sensitive to parameters such as initial chirping and fiber input power. The clock power dependence on the fiber dispersion is theoretically analyzed assuming that the return-to-zero (RZ) format is used and that pulse broadening is small compared to the bit duration. We show that the clock power is maximized when the dispersion-induced waveform distortion is minimized. Numerical simulations show that the proposed scheme is effective with the non-return-to-zero (NRZ) format and for the case that the optimum total dispersion deviates from zero due to initial and/or self-phase modulation (SPM)-induced chirping. The operation of the proposed automatic equalization system is experimentally confirmed in 20-Gbit/s transmission using both RZ and NRZ formats. Moreover, a 40-Gbit/s transmission experiment over 200 km of dispersion-shifted fiber (DSF) is successfully demonstrated using the proposed equalization scheme.
Rieko SATO Toshio ITO Katsuaki MAGARI Akira OKADA Manabu OGUMA Yasumasa SUZAKI Yoshihiro KAWAGUCHI Yasuhiro SUZUKI Akira HIMENO Noboru ISHIHARA
We fabricated a 1.55-µm polarization insensitive Michelson interferometric wavelength converter (MI-WC). The MI-WC consists of a two-channel spot-size converter integrated semiconductor optical amplifier (SS-SOA) on a planar lightwave circuit (PLC) platform. Clear eye opening and no power penalty in the back-to-back condition were obtained at 10 Gb/s modulation. We also confirmed the polarization insensitive operation on the input signal. Moreover, for an application of the MI-WC to DWDM networks, we demonstrated the selective wavelength conversion of 2.5 G/s optical packets from Fabry-Perot laser diode (FP-LD) light to four ITU-T grid wavelengths. We confirmed the good feasibility of this technique for use in DWDM networks. The wavelength conversion we describe here is indispensable for future all-optical networks, in which optical signal sources without wavelength control will be used at user-end terminals.
Rieko SATO Toshio ITO Katsuaki MAGARI Akira OKADA Manabu OGUMA Yasumasa SUZAKI Yoshihiro KAWAGUCHI Yasuhiro SUZUKI Akira HIMENO Noboru ISHIHARA
We fabricated a 1.55-µm polarization insensitive Michelson interferometric wavelength converter (MI-WC). The MI-WC consists of a two-channel spot-size converter integrated semiconductor optical amplifier (SS-SOA) on a planar lightwave circuit (PLC) platform. Clear eye opening and no power penalty in the back-to-back condition were obtained at 10 Gb/s modulation. We also confirmed the polarization insensitive operation on the input signal. Moreover, for an application of the MI-WC to DWDM networks, we demonstrated the selective wavelength conversion of 2.5 G/s optical packets from Fabry-Perot laser diode (FP-LD) light to four ITU-T grid wavelengths. We confirmed the good feasibility of this technique for use in DWDM networks. The wavelength conversion we describe here is indispensable for future all-optical networks, in which optical signal sources without wavelength control will be used at user-end terminals.
The authors propose and experimentally demonstrate an all-optical exclusive OR (XOR) logic gate based on self-phase modulation (SPM) of a semiconductor optical amplifier (SOA). The scheme is insensitive to the polarization of the input signal and requires no additional synchronized clock. The output of the XOR gate showed the contrast ratio of more than 17 dB for the input signal at 2.5 GHz.
Yoshikatsu AKITA Koji SHIBATA Takakazu SAKAI Atsushi NAKAGAKI
This paper shows the method of theoretical analysis for the bit error probability of the trellis-coded partial response continuous phase modulation (TCM-PR-CPM) over the correlated Rician fast frequency nonselective fading channel. In the analysis, the fading correlation of the channel and the effect due to finite interleaver are taken into account. By applying the method to the rate 1/2 (7, 2) trellis code with the raised cosine pulse of length 2 (2RC) partial response signaling, we show that the tighter upper bounds of the bit error rate are obtained than those in the preceding report.
Fumio FUTAMI Yuichi TAKUSHIMA Kazuro KIKUCHI
Aiming at wideband and flat supercontinuum generation (SC) from optical fibers in the 1.55-µm wavelength region, we study both experimentally and theoretically how SC spectra are influenced by group-velocity dispersion (GVD) of fibers. In the anomalous GVD region, since the peak power of pump pulses is kept high during propagation through the fiber by the higher-order soliton effect, the Raman effect has an adverse effect to flat and wideband SC generation. In the zero GVD region, the interplay of the third-order dispersion (TOD) and the self-phase modulation splits the SC spectrum into two main components. On the other hand, in the normal GVD region, nevertheless the SC spectrum broadens wider and smoother than those in anomalous and zero GVD regions, it is still asymmetric when TOD of the fiber can not be ignored. From these results, we find that a dispersion-flattened fiber with normal GVD is the most suitable for flat and wideband SC generation. A 280-nm wide SC spectrum with the spectral-density fluctuation less than 10 dB is actually generated from such a fiber.
Fumio FUTAMI Yuichi TAKUSHIMA Kazuro KIKUCHI
Aiming at wideband and flat supercontinuum generation (SC) from optical fibers in the 1.55-µm wavelength region, we study both experimentally and theoretically how SC spectra are influenced by group-velocity dispersion (GVD) of fibers. In the anomalous GVD region, since the peak power of pump pulses is kept high during propagation through the fiber by the higher-order soliton effect, the Raman effect has an adverse effect to flat and wideband SC generation. In the zero GVD region, the interplay of the third-order dispersion (TOD) and the self-phase modulation splits the SC spectrum into two main components. On the other hand, in the normal GVD region, nevertheless the SC spectrum broadens wider and smoother than those in anomalous and zero GVD regions, it is still asymmetric when TOD of the fiber can not be ignored. From these results, we find that a dispersion-flattened fiber with normal GVD is the most suitable for flat and wideband SC generation. A 280-nm wide SC spectrum with the spectral-density fluctuation less than 10 dB is actually generated from such a fiber.
Reiji SATO Masanori SHINRIKI Shinkichi NISHIMOTO
This paper investigates a new class of pulse compression codes in which the phase rotates clockwise, and afterward, rotates anticlockwise (or rotates anticlockwise, and afterward, rotates clockwise). The spectrum energy then concentrates to the narrower band compared to the conventional code such as the Barker code and the pulse is compressed not to the width of a single subpulses, but to the width made by a collection of several subpulses. It is revealed that, using the new code, PSL (Peak Sidelobe Level) can be reduced to -25.6 dB (1/19) -25.1 dB (1/18), which is much smaller than using the Barker code and Frank code, when the compression ratio is about 10 or larger. Furthermore, the signal-to-noise ratio after compression, the appropriate IF bandwidth and Doppler tolerance for the new code are estimated by simulation.
Yasuo YOKOTA Kazuhiko OGUSU Yosuke TANAKA
We present an experimental and theoretical study of multiple diffraction rings of a cw Ar+ laser beam from a nitrobenzene solution of BDN (bis-(4-dimethylaminodithiobenzil)-nickel) caused by the spatial self-phase modulation. We examine in detail the effect of the intensity and phase shift profiles of the beam in the nonlinear medium by comparing the measured ring patterns with the theoretical results based on the Fraunhofer diffraction. Although the thickness of the sample is only 180 µm in our experiment, it is found that the intensity and phase shift profiles are broadened owing to the self-defocusing effect. It is also found that the phase shift profile is further broadened by the thermal diffusion. These two effects become remarkable when the focused beam is used.
Norio OHKAWA Tetsuo TAKAHASHI Yoshiaki MIYAJIMA Mamoru AIKI
Repeaterless transmission system design employing remote pumping in a single fiber is clarified. The design is aimed to realize cost effective submarine transmission systems with easy maintenance. Remote pumping in a single fiber can extend repeaterless transmission distance without decreasing the system capacity per cable. It is applicable for high-count-fiber cable such as the 100-fiber submarine cable already developed. A simple but effective system configuration is presented that uses remote pumping from receiver end; both remote-pre erbium-doped fiber (EDF) amplification and backward pumping Raman amplification are employed. Stable transmission can be obtained without optical isolators, therefore the optical time domain reflectometry (OTDR) method is supported by this system. Three fiber configurations, which consist of dispersion shifted fiber (DSF), pure silica core fiber (PSCF) and a combination of DSF and PSCF, are examined to compare system performance. Remote-pre EDF is optimized in terms of length and location from receiver end by optical SNR (OSNR) calculations. Maximum signal output power is also determined through a waveform simulation based on the split-step Fourier method, in order to avoid waveform distortion caused by the combined effect of self-phase modulation (SPM) and group velocity dispersion (GVD). Through these calculations and simulations, we confirm the proposed repeaterless transmission system performance of 600Mbit/s-451 km with PSCF, 2. 5 Gbit/s-407 km with DSF + PSCF, and 10 Gbit/s-376 km with DSF+PSCF, which include system margin.
Kohichi TAMURA Eiji YOSHIDA Masataka NAKAZAWA
The effects of forced phase modulation (FPM) and self phase modulation (SPM) in dispersion tuned fiber lasers (DTFL) are examined. We show that FPM, such as chirp in the modulator, plays an important role in the pulse shaping because of the important role of dispersion in the cavity. In particular, compared to the case of zero FPM, significant pulse shortening can be obtained by using up-chirp modulation. The results suggest that modulators with large chirp parameters are desirable for DTFLs. When SPM is introduced, the pulse shapes differ greatly depending on the direction of the FPM. Significant deviations from Gaussian profiles are observed.
Shigenobu SASAKI Hisakazu KIKUCHI Jinkang ZHU Gen MARUBAYASHI
This paper investigates the error rate performance of parallel combinatorial spread spectrum (PC/SS) communicaion systems that use coherent and differential multiphase modulation: multiphase parallel combinatorial spread spectrum (MPC/SS) communication systems. The PC/SS systems are multicode SS systems based on orthogonal pseudo-noise (PN) sequences. Data is transmitted by delivering a combination of multiple PN sequences among a set of pre-assigned PN sequences. In the MPC/SS systems, every PN sequence on transmission is modulated by q-ary coherent or differential phase shift keying (PSK). Symbol error rate (SER) and average bit error rate (BER) in coherent and differential MPC/SS systems are investigated. The BER comparison between the MPC/SS systems and simple multicode SS systems with q-ary coherent and differential PSK is also presented. Numerical results show that the MPC/SS systems are superior to the conventional q-ary PSK systems, if they have equal spectral efficiency.